Truett & Osborn Flywheels

Replacement flywheels (stock cubic inch displacement) by year and model. See stroke availability chart below for additional stroke lengths. Big Twin flywheels from 1939-1999 are available in two different styles (TorqueMonster Weight and Lighter weight). The TorqueMonster flywheels are direct replacement weight (heavy) for years 1930-81. The left side flywheel is much wider & heavier than the right side. The Lighter weight flywheels are the same width and weight for both right and left sides (similar to Evolution flywheels and S&S). Late Shoveheads and Evolutions from 1982-1999 the Lighter weight would be the direct replacement weight. TorqueMonster weight is available for these models as an option to increase low-end torque in Evos.

Year/Model Fitment Specifications Model Codes
Years Engine Size/Model Stock Stroke Outside Diameter Notes TorqueMonster Weight Lighter Weight Price Qty.  
1929-1973 Harley 45" 3 13/16 7 7/8 HD45 $420.00
Add to Cart
1929-1973 Special HD 45" 3 13/16 7 7/8 Uses XL C-Pin/Rods HD45XL $470.00
Add to Cart
1952-1953 K Model 3 13/16 7 7/8 Press in shafts & C-pin 52K $420.00
Add to Cart
1954-1956 KH Model 4 9/16 7 7/8 Lip on sprocket hole 54KH $420.00
Add to Cart
1958-1970 XLR Model 3 13/16 7 7/8 XLR $420.00
Add to Cart
1957-E1981 Sportster 3 13/16 7 7/8 EXL $420.00
Add to Cart
L1981-1985 Sportster 3 13/16 7 7/8 LXL $420.00
Add to Cart
1986-2003 Sportster 3 13/16 7 7/8 S&S special shafts EVXL $420.00
Add to Cart
1915-1929 61" J Model 3 1/2 8 3/4 J $420.00
Add to Cart
1921-1929 74" JD Model 3 31/32 8 3/4 JD $420.00
Add to Cart
1930-1936 74" Flathead 3 31/32 8 1/8 4" stroke also avail. 30T $470.00
Add to Cart
1936 80" Flathead 4 1/4 8 1/8 30T $470.00
Add to Cart
1937-1948 74"/80" Flathead 4 9/32 8 9/32 Use 1941-later C-pin 37T $470.00
Add to Cart
1936-1940 61" Knucklehead 3 1/2 8 1/8 Use 1941-later C-pin 36T $470.00
Add to Cart
1941-1947 61" Knucklehead 3 1/2 8 1/2 39T $470.00
Add to Cart
1948-1952 61" Panhead 3 1/2 8 1/2 39T $470.00
Add to Cart
1941-1954 74" Pan/Knucklehead 3 31/32 8 1/2 39 $420.00
Add to Cart
1941-1954 74" Pan/Knucklehead 3 31/32 8 1/2 39T $470.00
Add to Cart
1955 74" Panhead 3 31/32 8 1/2 56-64 Sprocket Shaft 56 $420.00
Add to Cart
1955 74" Panhead 3 31/32 8 1/2 56-64 Sprocket Shaft 56T $470.00
Add to Cart
1956-1969 74" Pan/Shovelhead 3 31/32 8 1/2 56 $420.00
Add to Cart
1956-1969 74" Pan/Shovelhead 3 31/32 8 1/2 56T $470.00
Add to Cart
1970-1971 74" Shovelhead 3 31/32 8 1/2 56 $420.00
Add to Cart
1970-1971 74" Shovelhead 3 31/32 8 1/2 70T $470.00
Add to Cart
1972-1981 74" Shovelhead * 3 31/32 8 1/2 82-Up sprocket shaft 82/72 $420.00
Add to Cart
1972-1981 74" Shovelhead * 3 31/32 8 1/2 82-Up sprocket shaft 82/72T $470.00
Add to Cart
1972-1981 80" Shovelhead * 4 1/4 8 1/2 82-Up sprocket shaft 82/72 $420.00
Add to Cart
1972-1981 80" Shovelhead * 4 1/4 8 1/2 82-Up sprocket shaft 82/72T $470.00
Add to Cart
1982-1984 80" Shovelhead 4 1/4 8 1/2 82 $420.00
Add to Cart
1982-1984 80" Shovelhead 4 1/4 8 1/2 82T $470.00
Add to Cart
1985-1999 80" Evolution 4 1/4 8 1/2 82 $420.00
Add to Cart
1985-1999 80" Evolution 4 1/4 8 1/2 82T $470.00
Add to Cart

Flywheels for 74" & 80" OHV models are available in Lighter weight or TorqueMonster version.

Flywheels for 61" OHV & Big Twin Flathead models are only available in TorqueMonster version.
**See Note**

Flywheels for 45" Flathead, K-Model, Sportster and JD models are only available in stock weight.

NOTE: JD, 45XL, XLR, EVXL, K and KH flywheels are specialty flywheels, priced the same as TorqueMonster flywheels. HD45 flywheels & Sportster flywheels are priced the same as Lighter weight flywheels.

NOTE: 1972-81 Original Harley flywheels used sprocket shaft part #24001-72. This shaft was very large taper, set at 8 degrees, & had a lot of problems with slippage in the flywheel. Truett & Osborn makes their flywheels for these years to use the 1982-later 23909-80 shaft.

NOTE: Flywheels for 1937-48 Big Twin Flathead and 1936-40 61" Knucklehead are made with the 1941-later OHV crankpin, NOT the stepped crankpin as original. Truett & Osborn only makes the stock stroke flywheels (4-9/32 & 3-1/2) in the TorqueMonster version, but since they make them with the later crankpin, the only difference between these and 1939-later OHV flywheels is the outside diameter. They can take a set of 1939-later OHV Lighter weight or TorqueMonster flywheels that are available in other strokes and turn the O.D. to be used in Flathead or 61" Knuckle engines.

NOTE: Flywheels for Evolution Sportster models require the use of special "big taper" S&S brand sprocket shaft and pinion shaft. Other parts such as pinion gears and bearings must also be changed, depending on the year/model.

STROKE AVAILABILITY CHART
* = Available at extra charge for reducing outside diameter **See Note** X = Available
Model Code & Stroke 3 1/2" 3 13/16" 3 31/32" 4" 4 1/4" 4 5/16" 4 9/32" 4 7/16" 4 9/16" 4 1/2" 4 5/8" 4 3/4" 5"
HD45 X X X X
45XL (XL C-pin) X X X X
52K X
54KH X
XLR (Race XL) X
EXL & LXL X X X X X X
EVXL X X
J & JD Model X X X X X X
30T (Flathead) X X X
37T (Flathead) * * X * * * *
36T (OHV) X * * * * * *
39 & 39T X X X X X X X
56 & 56T X X X X X X
70T X
82/72 & 82/72T X X X X X X
82 & 82T X X X X X

** Please call for pricing and lead time.

Return Policy: The Good Old Motorcycle Parts Company accepts returns and/or exchanges on products within (30) days of receipt. We DO NOT accept any returns or exchanges on Electrical Components (remember if it smells burnt, it is burnt). All warranties on electrical components must be taken up with the individual manufacturer. The returned product must be in the original packaging, unopened and unaltered. The buyer is responsible for all shipping charges to exchange or return an item. Shipping charges will only be refunded on defective items, misrepresented items or items that may have been sent to you in error. If you are unsure about an item, a size or a fit, please contact us prior to purchasing the item.